ESP32-C2 has a single group timer, thus it will use it for the interrupt watchdog,
which is more critical than the task watchdog. The latter is implement in
software thanks to the `esp_timer`component.
dl.espressif.com is now using the same root certificate as github.com.
This commit replaces the previously-used ISRG X1 root certificate
with the DigiCert Root CA certificate.
As a result, even if the certificates are not installed (as it happens
on macOS with python.org installers, if the user forgets to run
'Install Certificates.command'), the download is successful.
Related to https://github.com/espressif/esp-idf/issues/4081
This commit fixes build issue because of function `bootloader_common_reset_rtc_retain_mem`
getting inlined with compiler optimization level set to `PERF` (-O2).
Build failure log:
-----------------
In function 'bootloader_common_reset_rtc_retain_mem',
inlined from 'bootloader_common_update_rtc_retain_mem' at /h/esp-idf/components/bootloader_support/src/bootloader_common_loader.c:183:13:
/h/esp-idf/components/bootloader_support/src/bootloader_common_loader.c:159:5: error: 'memset' writing 16 bytes into a region of size 0 overflows the destination [-Werror=stringop-overflow=]
159 | memset(rtc_retain_mem, 0, sizeof(rtc_retain_mem_t));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
update gpio_sig at `spics_out` array in each spi_periph.c of chips later than s2
then `spi_bus_add_device` can correctly distribute gpio_signals for cs_signal
Closes https://github.com/espressif/esp-idf/issues/8876
In previous gpio default isr, interrupt status bits get cleared at the exit of the isr.
However, for edge-triggered interrupt type, the interrupt status bit should be cleared before entering the per-pin handlers to avoid any potential interrupt lost.
Closes https://github.com/espressif/esp-idf/pull/6853
The actual output from the build tool (CMake/Ninja) may or may not
contain color escape codes, depending on various factors. The output
written to the log file should never include color escape codes,
though. This is because color escape codes in files are usually not
rendered as "color" in editors, and complicate reading. Also escape
codes would break the regular expressions used to display hints for
compilation errors.
If stdout is a TTY (meaning that the output is not redirected), tell
the build tool (GNU Make or Ninja) to enable colorized output.
GNU Make and Ninja also check if their stdout is redirected and
strip color escape sequences in that case. CLICOLOR_FORCE environment
variable overrides this behavior.
With this change, if the compiler was launched with the
-fcolor-diagnostics flag and idf.py output is not redirected, the
final output in the terminal will be colorized.
(-fcolor-diagnostics is handled at CMake level by the previous commit)
Related to https://github.com/espressif/esp-idf/issues/4162
Setting this option informs CMake that it should pass
-fcolor-diagnostics flag to the compiler.
(Colorized build system output, like from GNU Make, is produced even
without this flag.)
Note that if the build is done using Ninja and the build output is
redirected (not a TTY), Ninja will still strip the escape codes from
the output. For the case of idf.py, this is handled in the next
commit.
There are multiple changes in this commit:
1. Unify the RISC-V and ULP-FSM code paths in esp32ulp_mapgen.py.
It seems that these were originally introduced because `nm` output
for the RISC-V case contained symbol sizes, while for the ULP-FSM
no symbol sizes were reported. This makes sense, because the
ULP-FSM object files are produced from assembly source, symbol
sizes have to be added manually using the .size directive.
In the case of RISC-V, the object files are built from C sources
and the sizes are automatically added by the compiler.
Now 'posix' output format is used for both RISC-V and ULP-FSM.
2. Move BASE_ADDR out of esp32ulp_mapgen.py. This now has to be passed
from CMake, which should make it easier to modify if a new chip
with a different RTC RAM base address is added.
3. Add C++ guards to the generated header file.
4. Switch from optparse to argparse for similarity with other IDF
tools.
5. Add type annotations.
This fixes the issue with build output not being colorized on Windows,
while the hints messages are colorized.
The issue occurred because sys.stdout and sys.stderr get overridden
by colorama.init() at runtime, but the default argument
output_stream=sys.stdout holds the reference to the"original"
sys.stdout.
colorama.init() (which, by the way, gets called via a curious chain
of imports, via idf_component_tools.manifest and tqdm package)
overrides standard streams, on Windows only. The overridden streams
contain logic to convert ANSI color codes into Windows Console API
calls to colorize the text.
Since read_and_write_stream function used the default value of
output_stream evaluated at module loading time, it was using the
original sys.stdout, not the one overridden by colorama.
One extra note is that while this does fix the coloring issue, the
solution is a bit fragile, as it relies on one of the following
(on Windows):
- colorama.init() is called (this can change if idf-component-manager
stops importing tqdm)
- Sufficiently new version of Windows 10 is used, and ANSI color codes
support is enabled in the Registry.
Zim Kalinowski