/*
 Arduino.h - Main include file for the Arduino SDK
 Copyright (c) 2005-2013 Arduino Team.  All right reserved.

 This library is free software; you can redistribute it and/or
 modify it under the terms of the GNU Lesser General Public
 License as published by the Free Software Foundation; either
 version 2.1 of the License, or (at your option) any later version.

 This library is distributed in the hope that it will be useful,
 but WITHOUT ANY WARRANTY; without even the implied warranty of
 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 Lesser General Public License for more details.

 You should have received a copy of the GNU Lesser General Public
 License along with this library; if not, write to the Free Software
 Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 */

#ifndef MAIN_ESP32_HAL_TOUCH_NEW_H_
#define MAIN_ESP32_HAL_TOUCH_NEW_H_

#include "soc/soc_caps.h"
#include "esp_idf_version.h"

#if SOC_TOUCH_SENSOR_SUPPORTED
#if ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 5, 0) || SOC_TOUCH_SENSOR_VERSION == 3

#ifdef __cplusplus
extern "C" {
#endif

#include "esp32-hal.h"
#include "driver/touch_sens.h"

#if SOC_TOUCH_SENSOR_VERSION == 1  // ESP32
#define TOUCH_CHANNEL_DEFAULT_CONFIG()                                                                                     \
  {                                                                                                                        \
    .abs_active_thresh = {1000}, .charge_speed = TOUCH_CHARGE_SPEED_7, .init_charge_volt = TOUCH_INIT_CHARGE_VOLT_DEFAULT, \
    .group = TOUCH_CHAN_TRIG_GROUP_BOTH,                                                                                   \
  }
#elif SOC_TOUCH_SENSOR_VERSION == 2  // ESP32-S2 & ESP32-S3
#define TOUCH_CHANNEL_DEFAULT_CONFIG() \
  { .active_thresh = {2000}, .charge_speed = TOUCH_CHARGE_SPEED_7, .init_charge_volt = TOUCH_INIT_CHARGE_VOLT_DEFAULT, }
#elif SOC_TOUCH_SENSOR_VERSION == 3  // ESP32-P4
#define TOUCH_CHANNEL_DEFAULT_CONFIG() \
  { .active_thresh = {1000}, }
#endif

typedef uint32_t touch_value_t;

/*
 * Set time in us that measurement operation takes
 * The result from touchRead, threshold and detection
 * accuracy depend on these values.
 * Note: must be called before setting up touch pads
 **/
void touchSetTiming(float measure, uint32_t sleep);

#if SOC_TOUCH_SENSOR_VERSION == 1  // ESP32
/*
 * @param[in] duration_ms   The measurement duration of the touch channel
 * @param[in] volt_low      The low voltage limit of the touch channel
 * @param[in] volt_high     The high voltage limit of the touch channel
 */
void touchSetConfig(float duration_ms, touch_volt_lim_l_t volt_low, touch_volt_lim_h_t volt_high);

#elif SOC_TOUCH_SENSOR_VERSION == 2  // ESP32S2, ESP32S3
/*
 * @param[in] chg_times     The charge times of the touch channel
 * @param[in] volt_low      The low voltage limit of the touch channel
 * @param[in] volt_high     The high voltage limit of the touch channel
 */
void touchSetConfig(uint32_t chg_times, touch_volt_lim_l_t volt_low, touch_volt_lim_h_t volt_high);

#elif SOC_TOUCH_SENSOR_VERSION == 3  // ESP32P4
/*
 * Tune the touch pad frequency.
 * Note: Must be called before setting up touch pads
*/
void touchSetConfig(uint32_t _div_num, uint8_t coarse_freq_tune, uint8_t fine_freq_tune);
#endif

#if SOC_TOUCH_SENSOR_VERSION == 1
/*
 * Specific functions to ESP32
 * Tells the driver if it shall activate the ISR if the sensor is Lower or Higher than the Threshold
 * Default if Lower.
 * Note: Must be called before setting up touch pads
 **/
void touchInterruptSetThresholdDirection(bool mustbeLower);
#endif

/*
 * Read touch pad value.
 * You can use this method to chose a good threshold value
 * to use as value for touchAttachInterrupt.
 * */
touch_value_t touchRead(uint8_t pin);

/*
 * Set function to be called if touch pad value rises by given increment (threshold).
 * Use touchRead to determine a proper threshold between touched and untouched state.
 * */
void touchAttachInterrupt(uint8_t pin, void (*userFunc)(void), touch_value_t threshold);
void touchAttachInterruptArg(uint8_t pin, void (*userFunc)(void *), void *arg, touch_value_t threshold);
void touchDetachInterrupt(uint8_t pin);

/*
 * Returns true when the latest ISR status for the Touchpad is that it is touched (Active)
 * and false when the Touchpad is untoouched (Inactive).
 * This function can be used in conjunction with ISR User callback in order to take action
 * as soon as the touchpad is touched and/or released.
 **/
bool touchInterruptGetLastStatus(uint8_t pin);

/*
 * Set the default threshold for touch pads.
 * The threshold is a percentage of the benchmark value.
 * The default value is 1.5%.
 **/
void touchSetDefaultThreshold(float percentage);

/*
 * Setup touch pad wake up from deep sleep /light sleep with given threshold.
 * When light sleep is used, all used touch pads will be able to wake up the chip.
 **/
void touchSleepWakeUpEnable(uint8_t pin, touch_value_t threshold);

#ifdef __cplusplus
}
#endif

#endif /* ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 5, 0) || SOC_TOUCH_SENSOR_VERSION == 3 */
#endif /* SOC_TOUCH_SENSOR_SUPPORTED */
#endif /* MAIN_ESP32_HAL_TOUCH_H_ */