Jason2866
81 lines
1.9 KiB
Plaintext
81 lines
1.9 KiB
Plaintext
CONFIG_IDF_TARGET="esp32c6"
|
|
|
|
# Arduino Settings
|
|
CONFIG_FREERTOS_HZ=1000
|
|
CONFIG_AUTOSTART_ARDUINO=y
|
|
|
|
# Log Levels
|
|
# Boot Messages - Log level
|
|
CONFIG_BOOTLOADER_LOG_LEVEL_ERROR=y
|
|
# Arduino Log Level
|
|
CONFIG_ARDUHAL_LOG_DEFAULT_LEVEL_INFO=y
|
|
# IDF Log Level
|
|
CONFIG_LOG_DEFAULT_LEVEL_ERROR=y
|
|
|
|
# Default to 921600 baud when flashing and monitoring device
|
|
CONFIG_ESPTOOLPY_BAUD_921600B=y
|
|
CONFIG_ESPTOOLPY_BAUD=921600
|
|
CONFIG_ESPTOOLPY_COMPRESSED=y
|
|
CONFIG_ESPTOOLPY_MONITOR_BAUD_115200B=y
|
|
CONFIG_ESPTOOLPY_MONITOR_BAUD=115200
|
|
CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y
|
|
|
|
# libsodium
|
|
CONFIG_LIBSODIUM_USE_MBEDTLS_SHA=y
|
|
|
|
# NIMBLE
|
|
CONFIG_BT_ENABLED=y
|
|
CONFIG_BT_NIMBLE_ENABLED=y
|
|
CONFIG_BT_NIMBLE_EXT_ADV=n
|
|
CONFIG_BT_NIMBLE_HCI_EVT_BUF_SIZE=70
|
|
CONFIG_USE_BLE_ONLY_FOR_COMMISSIONING=n
|
|
|
|
# FreeRTOS should use legacy API
|
|
CONFIG_FREERTOS_ENABLE_BACKWARD_COMPATIBILITY=y
|
|
|
|
# Enable OpenThread
|
|
CONFIG_OPENTHREAD_ENABLED=y
|
|
CONFIG_OPENTHREAD_SRP_CLIENT=y
|
|
CONFIG_OPENTHREAD_DNS_CLIENT=y
|
|
CONFIG_OPENTHREAD_LOG_LEVEL_DYNAMIC=n
|
|
CONFIG_OPENTHREAD_LOG_LEVEL_NOTE=y
|
|
CONFIG_OPENTHREAD_CLI=n
|
|
|
|
# Disable lwip ipv6 autoconfig
|
|
CONFIG_LWIP_IPV6_AUTOCONFIG=n
|
|
|
|
# Use a custom partition table
|
|
CONFIG_PARTITION_TABLE_CUSTOM=y
|
|
CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="partitions.csv"
|
|
|
|
# LwIP config for OpenThread
|
|
CONFIG_LWIP_IPV6_NUM_ADDRESSES=8
|
|
CONFIG_LWIP_MULTICAST_PING=y
|
|
|
|
# MDNS platform
|
|
CONFIG_USE_MINIMAL_MDNS=n
|
|
CONFIG_ENABLE_EXTENDED_DISCOVERY=y
|
|
|
|
# Enable OTA Requestor
|
|
CONFIG_ENABLE_OTA_REQUESTOR=n
|
|
|
|
# Disable STA and AP for ESP32C6
|
|
CONFIG_ENABLE_WIFI_STATION=n
|
|
CONFIG_ENABLE_WIFI_AP=n
|
|
|
|
# Enable chip shell
|
|
CONFIG_ENABLE_CHIP_SHELL=n
|
|
|
|
# Disable persist subscriptions
|
|
CONFIG_ENABLE_PERSIST_SUBSCRIPTIONS=n
|
|
|
|
# MRP configs
|
|
CONFIG_MRP_LOCAL_ACTIVE_RETRY_INTERVAL_FOR_THREAD=5000
|
|
CONFIG_MRP_LOCAL_IDLE_RETRY_INTERVAL_FOR_THREAD=5000
|
|
CONFIG_MRP_RETRY_INTERVAL_SENDER_BOOST_FOR_THREAD=5000
|
|
CONFIG_MRP_MAX_RETRANS=3
|
|
|
|
# Enable HKDF in mbedtls
|
|
CONFIG_MBEDTLS_HKDF_C=y
|
|
|