Jason2866
91 lines
2.1 KiB
Plaintext
91 lines
2.1 KiB
Plaintext
CONFIG_IDF_TARGET="esp32c6"
|
|
|
|
# Arduino Settings
|
|
CONFIG_FREERTOS_HZ=1000
|
|
CONFIG_AUTOSTART_ARDUINO=y
|
|
|
|
# Log Levels
|
|
# Boot Messages - Log level
|
|
CONFIG_BOOTLOADER_LOG_LEVEL_ERROR=y
|
|
# Arduino Log Level
|
|
CONFIG_ARDUHAL_LOG_DEFAULT_LEVEL_INFO=y
|
|
# IDF Log Level
|
|
CONFIG_LOG_DEFAULT_LEVEL_ERROR=y
|
|
|
|
# Default to 921600 baud when flashing and monitoring device
|
|
CONFIG_ESPTOOLPY_BAUD_921600B=y
|
|
CONFIG_ESPTOOLPY_BAUD=921600
|
|
CONFIG_ESPTOOLPY_COMPRESSED=y
|
|
CONFIG_ESPTOOLPY_MONITOR_BAUD_115200B=y
|
|
CONFIG_ESPTOOLPY_MONITOR_BAUD=115200
|
|
CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y
|
|
|
|
#enable BT
|
|
CONFIG_BT_ENABLED=y
|
|
CONFIG_BT_NIMBLE_ENABLED=y
|
|
|
|
#disable BT connection reattempt
|
|
CONFIG_BT_NIMBLE_ENABLE_CONN_REATTEMPT=n
|
|
|
|
# NIMBLE
|
|
CONFIG_BT_NIMBLE_EXT_ADV=n
|
|
CONFIG_BT_NIMBLE_HCI_EVT_BUF_SIZE=70
|
|
CONFIG_USE_BLE_ONLY_FOR_COMMISSIONING=y
|
|
|
|
#enable lwip ipv6 autoconfig
|
|
CONFIG_LWIP_IPV6_AUTOCONFIG=y
|
|
|
|
# Use a custom partition table
|
|
CONFIG_PARTITION_TABLE_CUSTOM=y
|
|
CONFIG_PARTITION_TABLE_FILENAME="partitions.csv"
|
|
CONFIG_PARTITION_TABLE_OFFSET=0xC000
|
|
|
|
# Disable chip shell
|
|
CONFIG_ENABLE_CHIP_SHELL=n
|
|
|
|
# Enable OTA Requester
|
|
CONFIG_ENABLE_OTA_REQUESTOR=n
|
|
|
|
#enable lwIP route hooks
|
|
CONFIG_LWIP_HOOK_IP6_ROUTE_DEFAULT=y
|
|
CONFIG_LWIP_HOOK_ND6_GET_GW_DEFAULT=y
|
|
|
|
# disable softap by default
|
|
CONFIG_ESP_WIFI_SOFTAP_SUPPORT=n
|
|
CONFIG_ENABLE_WIFI_STATION=y
|
|
CONFIG_ENABLE_WIFI_AP=n
|
|
|
|
# Disable DS Peripheral
|
|
CONFIG_ESP_SECURE_CERT_DS_PERIPHERAL=n
|
|
|
|
# Use compact attribute storage mode
|
|
CONFIG_ESP_MATTER_NVS_USE_COMPACT_ATTR_STORAGE=y
|
|
|
|
# Enable HKDF in mbedtls
|
|
CONFIG_MBEDTLS_HKDF_C=y
|
|
|
|
# Increase LwIP IPv6 address number to 6 (MAX_FABRIC + 1)
|
|
# unique local addresses for fabrics(MAX_FABRIC), a link local address(1)
|
|
CONFIG_LWIP_IPV6_NUM_ADDRESSES=6
|
|
|
|
# libsodium
|
|
CONFIG_LIBSODIUM_USE_MBEDTLS_SHA=y
|
|
|
|
# FreeRTOS should use legacy API
|
|
CONFIG_FREERTOS_ENABLE_BACKWARD_COMPATIBILITY=y
|
|
|
|
# Use minimal mDNS
|
|
CONFIG_USE_MINIMAL_MDNS=y
|
|
CONFIG_ENABLE_EXTENDED_DISCOVERY=y
|
|
|
|
# ESP32-C6-DevKit Settings
|
|
# Buttons
|
|
CONFIG_BUTTON_PIN=9
|
|
# LEDs
|
|
CONFIG_WS2812_PIN=8
|
|
# max GPIO
|
|
CONFIG_ENV_GPIO_RANGE_MIN=0
|
|
CONFIG_ENV_GPIO_RANGE_MAX=30
|
|
CONFIG_ENV_GPIO_IN_RANGE_MAX=30
|
|
CONFIG_ENV_GPIO_OUT_RANGE_MAX=30
|